Wednesday, February 19, 2014
Browse Manual »
Wiring »
Circuit power amplifier 20w Bridge amplifier for car audio with Tda 2005 Read more Circuit power amplifier 20w Bridge amplifier for car audio with Tda 2005 Xtronic Free Electronic Circuits and Informations
.jpg)
Read more: Circuit power amplifier 20w Bridge amplifier for car audio with Tda 2005 | Xtronic Free Electronic Circuits and Informations http://xtronic.org/circuit/amplifier/amplifier-tda-2005-bridge-car-20-w/#ixzz2dAsqVStV
Circuit power amplifier 20w Bridge amplifier for car audio with Tda 2005 Read more Circuit power amplifier 20w Bridge amplifier for car audio with Tda 2005 Xtronic Free Electronic Circuits and Informations
DESCRIPTION
The TDA2005is class B dual audio power amplifier in MULTIWATT package specifically designed for car radio application : power booster amplifiers are easily designed using this device that provides a high current capability (up to 3.5 A) and that can drive very low impedance loads.
The TDA2005is class B dual audio power amplifier in MULTIWATT package specifically designed for car radio application : power booster amplifiers are easily designed using this device that provides a high current capability (up to 3.5 A) and that can drive very low impedance loads.
High output power : PO = 10 + 10 W@RL =2Ω, d = 10% ; PO = 20W@RL =4Ω ,d=1%.
High reliability of the chip and packagewith additional complete safety during operation thanks to protection against :
.OUTPUT DC AND AC SHORT CIRCUIT TO GROUND
.OVERRATING CHIP TEMPERATURE
.LOAD DUMP VOLTAGE SURGE
.FORTUITOUS OPEN GROUND
.VERY INDUCTIVE LOADS
Flexibility in use : bridge or stereo booster amplifiers with or without boostrap and with programmable gain and bandwidth.
Space and cost saving : very low number of external components, very simple mounting system with no electrical isolation between the package and the heatsink (one screw only).
In addition, the circuit offers loudspeaker protection during short circuit for one wire to ground.
High reliability of the chip and packagewith additional complete safety during operation thanks to protection against :
.OUTPUT DC AND AC SHORT CIRCUIT TO GROUND
.OVERRATING CHIP TEMPERATURE
.LOAD DUMP VOLTAGE SURGE
.FORTUITOUS OPEN GROUND
.VERY INDUCTIVE LOADS
Flexibility in use : bridge or stereo booster amplifiers with or without boostrap and with programmable gain and bandwidth.
Space and cost saving : very low number of external components, very simple mounting system with no electrical isolation between the package and the heatsink (one screw only).
In addition, the circuit offers loudspeaker protection during short circuit for one wire to ground.
Schematic diagram for power amplifier tda2005
Suggested PCB for mounting the amplifier tda2005 Bridge
Layout to guide the assembly of components on board the 20-watt amplifier
List of material to mount the amplifier tda2005
| Component | Value |
| C1,C2 | 2.2uF |
| C3,C4,C5 | 100nF |
| C6 | 10uF |
| C7,C8 | 100uF |
| C9,C10 | 220uF |
| C11 | 1000uF |
| IC1 | TDA2005M |
| IN | AK500/2 |
| OUT | AK500/2 |
| P1 | 100k |
| PWR | AK500/2 |
| R1 | 120K |
| R2 | 1K |
| R3,R4 | 1 |
| R5 | 2K |
| R6,R7 | 12 |
| Several | 12 volt power supply, wires, heat sink, board, etc. |
Read more: Circuit power amplifier 20w Bridge amplifier for car audio with Tda 2005 | Xtronic Free Electronic Circuits and Informations http://xtronic.org/circuit/amplifier/amplifier-tda-2005-bridge-car-20-w/#ixzz2dAsqVStV
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment